3G2646 8C9136 Wiper Seals 9X7333 1080134 3J7761 1080132 6E0036 9X7329 8C9146 3J4460 7J2806 8J1877 9X7323 1615789 9X7255

3G2646 8C9136 9X7333 1080134 3J7761 1080132 6E0036 9X7329 8C9146 3J4460 7J2806 8J1877 9X7323 1615789 9X7255 3J7622

SEAL-LIP TYPE 7X4750 -

9X7333 Seal Wiper Fits 769D 771C 771D 775B 775D 769C 770 772 773B

2253294 - Seal-Wiper 3J7622 1615789 1672497 9X7255 for ()

FIRST PRICE PARTS

Before performing any operation or maintenance procedures, ensure that the Safety Information, warnings, and instructions are read and understood. To determine the maintenance intervals, use fuel consumption, service hours, or calendar time, which ever occurs first.Before each consecutive interval is performed, all of the maintenance requirements from the previous interval must also be performed.Note: Some maintenance items are for optional equipment.When Required
Battery - Replace
Battery or Battery Cable - Disconnect
Engine Storage Procedure - Check
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Severe Service Appliion - Check
Daily
Cooling System Coolant Level - Check
Driven Equipment - Check
Engine Air Cleaner Service Indior - Inspect
Engine Air Precleaner - Clean
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Power Take-Off Clutch - Check/Adjust/Lubrie
Walk-Around Inspection
Every 3000 Service Hours or 3 Years
Cooling System Coolant (DEAC) - Change
Every 6000 Service Hours or 6 Years
Cooling System Coolant (ELC) - Change
First 19 000 L (5000 US gal) of Fuel or 250 Service Hours
Engine Valve Lash - Inspect/Adjust
Every 19 000 L (5000 US gal) of Fuel or 250 Service Hours
Aftercooler Core - Clean/Test
Alternator and Fan Belts - Inspect/Adjust/Replace
Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Electronics Grounding Stud - Inspect/Clean/Tighten
Engine Air Cleaner Element (Dual Element) - Clean/Replace
Engine Air Cleaner Element (Single Element) - Replace
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fan Drive Bearing - Lubrie
Fuel System Secondary Filter - Replace
Hoses and Clamps - Inspect/Replace
Radiator - Clean
Every 38 000 L (10 000 US gal) of Fuel or 500 Service Hours
Engine Crank Breather - Clean
Fuel System Primary Filter (Water Separator) Element - Replace
Every 228 000 L (60 000 US gal) of Fuel or 3000 Service Hours
Air Compressor - Inspect
Cooling System Coolant Extender (ELC) - Add
Cooling System Water Temperature Regulator - Replace
Crankshaft Vibration Damper - Inspect
Engine - Clean
Engine Mounts - Inspect
Engine Speed/Timing Sensors - Check/Clean/Calibrate
Engine Valve Lash - Inspect/Adjust
Engine Valve Rotators - Inspect
Every 379 000 L (100 000 US gal) of Fuel or 5000 Service Hours
Alternator - Inspect
Starting Motor - Inspect
Turbocharger - Inspect
Water Pump - Inspect
Overhaul
Overhaul Considerations

Ammeters

1W8914
2W5111
Service Meter
9G6762, 6T7337
(1) Tighten two nuts on back to a torque of ... 0.40 0.08 N m (4 1 lb in) (1) Torque for bolts which hold service meter ... 10.9 2.8 N m (96 24 lb in)Pressure
1W0707
2W3687
1W0706
Oil Pressure
7W2937 Gauge 24V; Use With 9X1124 Sending Unit
Range ... 0 to 550 kPa (0 to 80 psi)Test voltage ... 27.2 .3 V Prior to inspection warm up indior for a minimum of five minutes with 27.2 Volts applied. Check calibration with descending pointer.7W2936 Gauge 12V
Range ... 0 to 550 kPa (0 to 80 psi)Test voltage ... 13.8 .3 V Prior to inspection warm up indior for a minimum of five minutes with 13.8 Volts applied. Check calibration with descending pointer. 5L7455 Gauge 12V; Use With 5L7450 Sending Unit
Range ... 0 to 550 kPa (0 to 80 psi)Test voltage ... 14V Prior to inspection warm up indior for a minimum of five minutes with 14 Volts applied. Check calibration with descending pointer. 4W2065 Gauge 24V
Range ... 0 to 550 kPa (0 to 80 psi)Test voltage ... 27.2 0.3V Prior to inspection warm up indior for a minimum of five minutes with 27.2 Volts applied. Check calibration with descending pointer. 5L7456 Gauge 24V; Use With 5L7450 Sending Unit
Range ... 0 to 550 kPa (0 to 80 psi)Test voltage ... 28.5 0.3V Prior to inspection warm up indior for a minimum of five minutes with 28.5 Volts applied. Check calibration with descending pointer.
Gauge With Color Code.1W4304
2W3681
Gauge with color code.